April 19

Lesson 08 – Equipment Needed

Lesson Eight: Equipment Needed To Keep Bees

As you prepare to keep bees, several tools will make it much easier. Of course, you could do without the tools and probably get by, but these tools have become the best friend to the beekeeper.

Let me start by sharing what I feel is ABSOLUTELY essential, and then I’ll talk about extras that just make the job easier.


1) Hive Tool
2) Smoker
3) Hat & Veil


When I first started keeping bees I really didn’t understand what the big deal was regarding the hive tool. Beekeepers talked about it like a carpenter talks about a hammer or tape measure. Now, three years later, my hive tool is my best friend in the apiary.

By the way, APIARY is a fancy word for where you keep your bees. It is pronounced like: a-pea-airy. Our actual business is called Long Lane Apiary, but since many people aren’t familiar with what an apiary is, we go by Long Lane Honey Bee Farms. Back to the hive tool.

A hive tool is between 9-10 inches long. I prefer the 9″ hive tool. The 10″ tool just seems too long and clumsy for me. It looks at first like a small carpenter’s pry bar. But, it is a hive tool. You will not find them at the local hardware store or at the local home supply center. You may think you don’t need one or that another shop tool will work, but take my advice, get a hive tool! One of my friends preferred to use a screw driver until he realized he was tearing up the hives. You’d better get two or three hive tools if you are like me, and lose them so quickly.

Here’s what the hive tool looks like:

The shinny end is mostly used for separating the hive bodies and supers. Bees gather propolisand use it as glue to keep their boxes tightly together. When inspecting your hive, you will need to use this hive tool to separate stuck-together pieces.

The hooked end of the hive tool is used mostly for scraping off the propolis. It is important to scrap off as much excess propolis as you can to prevent build up and to keep a cleaner hive.
Notice the small hole in the hive tool. This is for pulling out nails if needed. Of course, you’ll find many more helpful uses for your hive tool, but these are everyday uses.

I would not want to keep bees without a smoker. Some brag that they don’t smoke their bees, but, to me, this is not practical. Okay, first, why blow smoke in a hive? We do it to calm the bees. The idea is that smoke causes the bees to gorge themselves on honey, which makes them less likely and almost unable to sting. For one, they are busy eating, and they become so full, they are unable to bend and sting. It really does work! Trust me, this is not a tool you’ll want to be without.

We’ll cover how to enter a hive in a future lesson, but for now, let me give a brief explanation on how to smoke your hive. Use pine needles, burlap or corn cobs as fuel for your smoker. Of course, you can use other items such as wood pellets, large saw dust, dried grass or mulch too. Make sure that whatever you burn has not been treated with chemicals as this could kill your bees. When approaching your hive to open it, blow a couple of puffs of smoke into the front opening and wait at least 3 minutes. Then, remove the top cover and gently blow a few puffs of smoke into the entrance hole on the inner cover. As you begin removing the inner cover, blow a few puffs of smoke under the inner cover and between the frames as you lift off the inner cover. It is a good idea to wait a few minutes after blowing smoke into the hive as this gives the bees time to eat and relax.

When lighting your smoker, do not pack it full, then try to light it. Load it lightly, and add fuel as it starts burning good. Be careful that the flame coming out of the opened smoker does not burn your hand or burn a nice size hole in your protective gear (experience speaking here)!!

Also, do not squeeze the smoker billow hard when smoking your hive. Gentle!! If you squeeze too hard, you may send fire into your hive. This is not good for the bees, and could set your entire hive on fire. Smoke only please!

Smoke does not hurt the bees. And you’ll get good enough to know how much to use after a few tries. The smoker is good too, in case you get stung, you should blow smoke around the area of the sting. Bees are attracted to the scent of a stinger as a target, so by smoking the sting area, you neutralize this scent. Don’t waste your money on expensive smokers! You’re only blowing smoke!! A $30 smoker is all you need and works well.

Okay, I admit, I have worked my bees without a hat or veil. And I also admit I have been stung on the face too. That’s one place I don’t like to get stung. And you could lose your sight if stung in the eye ball. And, if you get stung on the lip, you will look like Donald Duck for 2 days! Wear a hat and veil at all times.


An occasional stray bee can sneak in beneath your veil.  What do you do then? First, you do not panic. She is not in there to kill you. She wandered in by accident.  Here’s what I do….face the sun, tilt your head back. She will move toward the sun on my inside veil, and I simply squeeze her between my fingers. The veil is flexible enough that I usually squeeze from the outside, but you can always slip your hand under your veil inside and squeeze her.


Some consider gloves nonessential, but I wear my gloves.  I hope to one day be able to work my hives without them…and sometimes I do….but for the most part I wear gloves.


Spray bottle, frame puller, frame holders, boots, etc.

Again, the plan is to work your bees in such a way as to never get stung. I’ll cover that in a future lesson too.